Energy performance of buildings. Heating and DHW systems in buildings - Measured energy performance, Module M3-10, M8-10

Energy performance of buildings. Heating and DHW systems in buildings - Measured energy performance, Module M3-10, M8-10

£322.00
£322.00
£161.00
Sold out

1   Scope

This European Standard specifies methods to assess the delivered energy for space heating and domestic hot water energy performance of a building based on measurements during the operation and occupancy phase. This includes:
  • — assessment of the amount of delivered energy carriers for space heating and domestic hot water preparation based on measurement;
  • — assessment of the energy performance indicators of heating and domestic hot water systems and subsystems based on measurements.
This standard does not cover the measurement of delivered energy for ventilation, cooling, air conditioning and lighting systems.
This standard includes procedures to correct measured delivered energy according to climate and building use.
Weighting (e.g. conversion into primary energy, cost, CO2 emission) of the measured delivered energy and assessment of the energy performance are covered in EN ISO 52000‑1:2017.
Table 1 shows the relative position of this standard within the set of EPB standards in the context of the modular structure as set out in EN ISO 52000‑1:2017.

NOTE 1 In CEN ISO/TR 52000‑2:2017 the same table can be found, with, for each module, the numbers of the relevant EPB standards and accompanying technical reports that are published or in preparation.

NOTE 2 The modules represent EPB standards, although one EPB standard may cover more than one module and one module may be covered by more than one EPB standard, for instance a simplified and a detailed method respectively. See also Clause 2 and Tables A.1 and B.1.

Table 1 — Position of this standard, within the modular structure of the set of EPB standards
  Overarching Building
(as such) 		Technical Building Systems
SUbmodule Descriptions   Descriptions   Descriptions Heating Cooling Ventilation Humidification Dehumidification Domestic Hot water Lighting Building automation and control Electricity production
sub1   M1   M2   M3 M4 M5 M6 M7 M8 M9 M10 M11
1 General   General   General EN 15316–1         EN 15316–1      
2 Common terms and definitions;
symbols, units and subscripts		   Building Energy Needs   Needs           EN 12831–3      
3 Applications   (Free) Indoor Conditions without Systems   Maximum Load and Power EN 12831–1         EN 12831–3      
4 Ways to Express Energy
Performance		   Ways to Express Energy Performance   Ways to Express Energy Performance EN 15316–1         EN 15316–1      
5 Building categories and Building Boundaries   Heat Transfer by Transmission   Emission and control EN 15316–2 EN 15316–2              
6 Building Occupancy and Operating Conditions   Heat Transfer by Infiltration and Ventilation   Distribution and control EN 15316–3 EN 15316–3       EN 15316–3      
7 Aggregation of Energy Services and Energy Carriers   Internal
Heat Gains		   Storage and control EN 15316–5         EN 15316–5 15316–4–3      
8 Building zoning   Solar
Heat Gains		   Generation                  
8–1         Combustion boilers EN 15316–4–1         EN 15316–4–1      
8–2         Heat pumps EN 15316–4–2 15316–4–2       EN 15316–4–2      
8–3         Thermal solar
Photovoltaics
 EN 15316–4–3         15316–4–3     15316–4–3
8–4         On-site cogeneration EN 15316–4–4         EN 15316–4–4     EN 15316–4–4
8–5         District heating and cooling EN 15316–4–5 EN 15316–4–5             EN 15316–4–5
8–6         Direct electrical heater EN 15316–4–8         EN 15316–4–8      
8–7         Wind turbines                 EN 15316–4–10
8–8         Radiant heating, stoves EN 15316–4–8                
9 Calculated Energy Performance   Building Dynamics (thermal mass)   Load dispatching and operating conditions                  
10 Measured
Energy
Performance		   Measured Energy Performance   Measured Energy Performance EN 15378–3         EN 15378–3      
11 Inspection   Inspection   Inspection EN 15378–1         EN 15378–1      
12 Ways to Express Indoor Comfort     – BMS                  
13 External Environment Conditions                          
14 Economic Calculation EN 15459–1                        

NOTE The shaded modules are not applicable